Custom PC Industrial Laboratory Analyzer Sample Tray

Material: ABS/POM/PA66/PP/PC/PA/PU/TPE/TPU etc.
Processing Service: Injection
Drawing Format: STP, STEP, IGS
Contact: amanda@tjswks.com / 0086-15222707659
Send Inquiry
Description

Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pc industrial laboratory analyzer sample tray in China. If you're going to buy bulk cheap custom pc industrial laboratory analyzer sample tray, welcome to get quotation from our factory. Quality products and low price are available.

 

Custom PC Industrial Laboratory Analyzer Sample Tray

SWKS develops custom injection molded PC components for industrial equipment. This page outlines the application, drawing inputs and validation points for the laboratory analyzer sample tray. Share the operating conditions and assembly model so the material grade and molded features can be reviewed for your equipment.

Registered Cup Positions for an Analyzer

A laboratory analyzer tray has to carry the samples and present each cup to the instrument in a predictable location. This SWKS custom PC molding is specified around the instrument bay and sample containers. A tray can move by hand, lift into a carrier or slide along guided surfaces, depending on the instrument design. A buyer supplies the loading direction and stop positions with the well layout. If the device has a reading head, probe or gripper, include its access envelope in the assembly information. The required clearance can be different at the edges of the tray and at intermediate pockets.

Identify the range of cup formats and whether there is one approved tray for each format. A well can locate on the wall, a support around the rim or a feature lower in the cup. That support changes how shoulder diameter, rim height and taper affect seating. The drawing should identify the cup surfaces that are allowed to touch and the points that need clearance for extraction. A photograph of a loaded tray helps a supplier see which direction an operator grips a cup when the neighboring wells are full.

a laboratory analyzer loading station

Illustrative rendering of a laboratory analyzer loading station. Production geometry follows the approved drawing.

Why the Pocket Array Needs a Coordinate Reference

A useful sample tray drawing puts the pocket centers in the same coordinate system as the instrument stops and guide surfaces. A support face supplies a height reference, while rails or a hard stop constrain translation. The loading geometry can distinguish front from back or left from right if the instrument expects a fixed mapping. Identify any features used by latches or sensors. For semi automatic loading, define which rails take the initial insertion and what condition confirms the tray has reached its seated position.

An instrument recipe may assume a fixed spacing from the first cup to the last. Inspect pockets near the datum and at the far edge using the same locating method. For a specific well, check the shape and the seated cup center separately where that is important. A tray can place a centered cup at the wrong height if the cup shoulder stops early. Document whether testing uses a cup gage, genuine sample container or another target. On larger arrays, include both corners and center locations to observe how the tray behaves across the span.

Polycarbonate Options and the Cleaning Protocol

Polycarbonate grade selection depends on the intended duty, including clarity where relevant, load and any cleaning agents used by the laboratory. The full PC grade, color and supplier documentation should be selected for the project. A clear component can provide visibility beneath a rack. Translucent or opaque colors may serve a different instrument requirement. If the analyzer uses optical cues, identify the surfaces and lighting conditions with the specification instead of applying a general appearance instruction to the whole part.

Cleaning compatibility belongs in the operating data. Document concentrations, temperature, wipe or immersion time, rinsing and drying. Use the approved conditioning program for the final grade and geometry, especially when liquids may contact a loaded molded tray. Areas near corners or fasteners can experience imposed strain while the component is exposed. For sample programs, record whether the cleanliness criterion relates to appearance, sample recovery, cross contamination control or access to specific recesses. The owner of the analyzer determines the laboratory method and scope for those checks.

Tooling the Rim, Wells and Underside

A broad tray can carry stiffening features below its platform. Their placement depends on what areas need support, where guides engage and whether the tray nests for transport. Wall transitions around wells may affect the shape above the ribs. Tool engineers can compare the cost and feasibility of different gate locations with the buyer's requirements for flatness and appearance. Mark the surfaces that touch rails and sample cups before the initial design review, as those interfaces may limit choices for ejection or mold split.

Operator contact matters around the rim. A handling pocket or textured zone can be defined if the analyzer layout leaves limited access. An identification panel or molded well numbering can help trace sample position. Style, size and reading direction of engraved marks belong on the approved drawing. If numbers are applied later, indicate the region and any required resistance to the cleaning cycle. Preserve mounting surfaces and rub zones during packaging to prevent out of box obstructions at loading.

Test From Full Insertion Through Unloading

A tray can be inspected empty for dimensional fit and then with the firm's specified set of sample cups. Change the distribution of cups only when the application requires those load patterns and record the conditions for comparison. Observe the force or kinematic check required by the analyzer owner. If the tray engages in steps, record the positions at which the support or a stop is contacted. Account for any movement from the sample handling mechanism once the tray is in place.

Common order inputs include the controlled PC designation, the cup and bay drawings, and the coordinate system used by the instrument. If a selected sample cup drawing belongs to a supplier, list the model or release that should be used for testing. Describe the required surface condition, cleaning exposure and the expected quantity over the tool life. A pilot lot can be identified by cavity and process condition so verification can be repeated after storage or conditioning.

sample pocket and registration edge

Illustrative rendering of sample pocket and registration edge. Production geometry follows the approved drawing.

Mapping the Last Pocket to the Analyzer

Setup should step through the full tray, including the pockets farthest from the registration datum. A small change in pitch can add up over several rows, while a single pocket can also shift locally because of the shape of its support. Record the pocket number, cup geometry and method used for each measurement. An empty tray can be evaluated for seating, then repeated using the cup weights and positions selected by the laboratory equipment owner.

Label the package and trial lots to identify resin grade, color and tool revision. Where a clear PC grade is requested, agree which windows must maintain visibility and where normal molding marks can be accommodated. When a separate label or printed code pairs sample coordinates with software records, communicate the position and orientation as drawing requirements. Handling tests can include insertion and removal with the intended operator tools or gloves so any issue is seen on the fixture before the molded trial is approved.

Show the whole interface for sample tray registration and indexing

Include an assembly section with the sample cups, analyzer loading rails and registration points. Place dimensional references on those parts that govern fit during use, and identify what may be adjusted during a tooling review. If the product drawing is based on a service sample, include a second reference showing the intended geometry where the sample has worn. The assembly section should show how the component goes into position and what it contacts during installation. A dimension that matters for removing it can be different from a dimension used to confirm the final working position.

On the print used for inspection, distinguish dimensions measured on a molded component from checks made with the loaded tray seated in a representative analyzer fixture. Mark any change in condition required by the customer, including material conditioning or the actual fitted hardware. Supply any gauge or test sample needed to reproduce the check. If an inspection fixture uses different references from the production equipment, show how each result relates to the desired fit. This makes it easier to compare prototype measurements and repeat production.

Record observations in service and at first approval

When discussing equipment that has already been in service, record cup size variation, distorted guide rails and dried residue if they are relevant. These observations should be mapped to the actual station and compared with nominal drawings. A replacement can appear to reproduce the worn shape while missing an original clearance or contact region. Keep photos before and after the trial and note which mating parts were changed during the evaluation. Report observations around pocket position and access to the last row of samples, and separate changes in surrounding elements from dimensional results for the molded part.

Customers ordering more than one version can provide a set of acceptance records by tray orientation and sample container reference. Give the first-article quantity for each combination and explain which checks will happen at the customer's plant. Approval should identify the exact drawing used to accept the sample and any equipment changes still under review. Procurement can use the approved drawing reference on repeat orders and keep associated sample reports with the relevant assembly. If the order covers secondary operations or purchased hardware, identify those items separately so they can be matched to the correct version.

Prepare the conditions for a repeat order

Where production continues with the same drawing, mark the characteristics that must be checked by lot or cavity. Give any labeling and packaging requirements that protect the working faces. A customer choosing between several configurations can supply their quantities and time needed for review independently. If a new revision is initiated later, indicate which assembly constraints drove the change and whether previous samples remain applicable. This keeps the fit and production evidence connected to the intended equipment.

Request a Drawing Review and Quotation

Browse our plastic injection parts and our injection molding design guide for related application information. Send your STP, STEP or IGS drawing, critical dimensions, operating conditions and target quantity to amanda@tjswks.com or call 0086-15222707659.

Hot Tags: custom pc industrial laboratory analyzer sample tray, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, Design PC Injection Molded Machine Plastic Parts, PE Injection Molding Plastic Machine Parts, perforated plastic sheet, Plastic Injection Conduit Molding Machine Parts, PP Hard Injection Automotive Plastic, Small batch injection molding

Send Inquiry

Send Inquiry