Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial bottle filling machine timing screw in China. If you're going to buy bulk cheap custom pom industrial bottle filling machine timing screw, welcome to get quotation from our factory. Quality products and low price are available.
Custom POM Industrial Bottle Filling Machine Timing Screw
SWKS develops custom injection molded POM components for industrial equipment. This page outlines the application, drawing inputs and validation points for the bottle infeed timing screw. Share the operating conditions and assembly model so the material grade and molded features can be reviewed for your equipment.
What an infeed timing screw controls
A bottle filling line can use a rotating timing screw to establish container spacing before handoff to a star wheel, filler or another indexing mechanism. Its helical channel works with the opposing guide and the bottle profile. Draw the installation with the complete transfer path and identify the point where the screw begins to engage each bottle. The illustrated acetal part represents one possible form. The customer's package and equipment geometry control the finished pitch, profile and mounting arrangement.
A bottle can approach the screw upright while its body, shoulder or base contacts different guiding surfaces. Identify the actual contact height. A nominal body diameter at the widest point can be misleading if the working region is lower or if the bottle is oval or tapered. Show the infeed rails and accepted path under realistic conditions. For a replacement, mark the side and station at which the original screw was installed and indicate the direction in which containers travel.

Illustrative rendering of bottles entering a filler. Production geometry follows the approved drawing.
Inlet shape and transition to the filler
The groove at entry must accept the presented container envelope and bring it into the intended spacing. Provide dimensional bottle data, the allowable spread across production lots and any ribs, label seams or handles that can reach the contact surface. Include the inlet guide shape and the way the conveyor advances the bottles. Different bottle finishes can leave different marks after contact, so an approval trial should use samples of the actual package whenever possible.
At discharge, show how the next station accepts the bottle. A screw dimensioned only as a loose component leaves out the star wheel pockets or other elements that establish the final transition. Identify the motion reference and any timing marks used during setup. A design review can compare positions at entry, halfway through the working length and at discharge. Those views explain whether a geometry change will affect spacing only at one point or through a larger part of the transfer path.
Hand, pitch and rotational references
A drawing should clearly show whether the groove is right handed or left handed, the viewing direction and the approved rotation. A photo taken from the opposite end can reverse the apparent orientation. Give the axial position and rotational relationship of the inlet and outlet features to an agreed datum. If pitch varies along the length, supply the complete CAD surface or approved sections rather than expecting a constant pitch note to describe the working channel.
Indicate the relationship between the screw and the drive key, mounting pin or coupler. Some installations rely on a positive feature while others allow the operator to time the part during changeover. Record what fixes axial location and where phase is measured. When the screw is part of a matched format set, confirm which rails and star wheel are approved with it. A record of the setup can make it easier to identify the correct version when similar screws are kept in stock.
Choose POM with the bottles and washdown in mind
Acetal is commonly considered for guiding and wear components. Give the approved grade if one already exists and describe what the groove contacts, including bottle material and any product or coating that may transfer to the part. Supply exposure details for cleaners, washdown and temperature changes where relevant. A resin grade is assessed with the specific contact and service conditions, not simply by the material family printed in a catalogue.
Clarify whether the screw contacts only the outside of a closed container or has another exposure condition defined by the application. If the customer has material documentation requirements, send them for review. During a representative trial, note whether marks appear on the bottle, the guide or the screw. A contact line may be intended while a scuff at a sharp transition could point to a local fit issue. Compare the assessment with the bottle and rail geometry referenced in the original drawing.
Shaft connections and service clearance
Show both ends of the screw in section. Include any insert, pin, collar or retaining screw that belongs to the mounting stack. A drive connection may transmit rotation at one end while the opposite end locates or supports the shaft. Define how the operator removes the change part using the equipment owner's procedures and confirm that surrounding components leave the required access. If the screw is supplied as a body and hardware is reused, identify the reused parts explicitly.
A fixed end register may set the groove location relative to the bottle handoff. Inspect the installed axial position using this reference rather than measuring from an unimportant end face. For applications with interchangeable supports, list the accepted support revisions. A reused collar or pin can alter fit or phase even when the molded body dimensions are correct. Document which parts were used on the first article and which will be supplied with repeat orders.
Decide whether the geometry suits injection molding
A long helical part deserves an early design-for-manufacturing check. The geometry, quantity and finish requirements determine whether an injection-molded body, a multi-piece solution or a different manufacturing method should be discussed. Provide the full working surface and mark the areas that cannot accept a parting or gate witness. Review whether an intended part can be removed from a proposed mold and whether a molded or secondary-processed end interface is needed.
Different wall sections can affect the as-produced shape. Identify the required centerline, groove profile and reference locations for measurements. If the screw is inspected on a fixture, show how the supports approximate the installed condition. Tool samples can then be checked for the relationship between the groove, shaft and handoff references. Keep the tool revision and inspection setup with the sample report so later results can be compared.

Illustrative rendering of helical channel and shaft connection. Production geometry follows the approved drawing.
Approval and repeat ordering
Use the specified bottle family and matching line hardware for a trial. Start by checking fit and timing against the approved setup, then observe where the bottle enters and where the following station takes over. Record the operating condition and the guide setting used in the trial. A sample that works with one container can require a different check at the dimensional limits of the approved range. Keep bottle and machine revisions with the acceptance record.
Send the original screw or approved model, cylinder and shaft references, bottle drawings, initial sample need and expected quantities. Mark wear on any service sample before using it as a geometry reference. If several package formats share a shaft, give separate quantities and marking requirements for their screws and matching guides. An inquiry that includes the complete transfer context allows the molding team to identify feasibility questions before committing to tooling.
Show the whole interface for bottle entry and discharge
Include an assembly section with the container outline at the working height, both guide rails and the receiving star wheel. Place dimensional references on those parts that govern fit during use, and identify what may be adjusted during a tooling review. If the product drawing is based on a service sample, include a second reference showing the intended geometry where the sample has worn. The assembly section should show how the component goes into position and what it contacts during installation. A dimension that matters for removing it can be different from a dimension used to confirm the final working position.
On the print used for inspection, distinguish dimensions measured on a molded component from checks made with the screw mounted and clocked on both supports. Mark any change in condition required by the customer, including material conditioning or the actual fitted hardware. Supply any gauge or test sample needed to reproduce the check. If an inspection fixture uses different references from the production equipment, show how each result relates to the desired fit. This makes it easier to compare prototype measurements and repeat production.
Record observations in service and at first approval
When discussing equipment that has already been in service, record a worn helical groove, shaft play and a changed bottle format if they are relevant. These observations should be mapped to the actual station and compared with nominal drawings. A replacement can appear to reproduce the worn shape while missing an original clearance or contact region. Keep photos before and after the trial and note which mating parts were changed during the evaluation. Report observations around the inlet groove and outlet handoff, and separate changes in surrounding elements from dimensional results for the molded part.
Customers ordering more than one version can provide a set of acceptance records by container lot and machine setup. Give the first-article quantity for each combination and explain which checks will happen at the customer's plant. Approval should identify the exact drawing used to accept the sample and any equipment changes still under review. Procurement can use the approved drawing reference on repeat orders and keep associated sample reports with the relevant assembly. If the order covers secondary operations or purchased hardware, identify those items separately so they can be matched to the correct version.
Prepare the conditions for a repeat order
Where production continues with the same drawing, mark the characteristics that must be checked by lot or cavity. Give any labeling and packaging requirements that protect the working faces. A customer choosing between several configurations can supply their quantities and time needed for review independently. If a new revision is initiated later, indicate which assembly constraints drove the change and whether previous samples remain applicable. This keeps the fit and production evidence connected to the intended equipment.
Request a Drawing Review and Quotation
Browse our plastic injection parts and our injection molding design guide for related application information. Send your STP, STEP or IGS drawing, critical dimensions, operating conditions and target quantity to amanda@tjswks.com or call 0086-15222707659.
Hot Tags: custom pom industrial bottle filling machine timing screw, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, complex plastic injection parts, injection molded plastic parts, PC machine parts, pc parts, plastic injection manufacturing parts, toy plastic injection parts






