Custom POM Industrial Packaging Machine Star Wheel

Custom injection molded POM packaging star wheel for bottle transfer on a packaging machine. Specify the mating geometry, operating conditions and order quantities for tooling and part review.
Send Inquiry
Description

Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial packaging machine star wheel in China. If you're going to buy bulk cheap custom pom industrial packaging machine star wheel, welcome to get quotation from our factory. Quality products and low price are available.

 

Custom POM Industrial Packaging Machine Star Wheel

This custom POM packaging star wheel is supplied to the approved drawing. Send the design and operating information for the bottle transfer on a packaging machine to review the part and tooling scope.

Part material POM
Other custom materials ABS / POM / PA66 / PP / PC / PA / PU / TPE / TPU
Processing Injection molding
Drawing formats STP / STEP / IGS

A star wheel registers the bottle at transfer

A packaging machine star wheel rotates containers through pockets shaped for their outside profiles. A guide rail usually supports the opposite side as a bottle moves from the inlet conveyor toward a filler, capper or discharge conveyor. The working envelope depends on the actual bottle, the guide rail and the adjacent machine, so the star wheel is built to the approved format geometry. The illustrated wheel shows one possible pocket arrangement and hub type. A replacement request should identify the original line and the position occupied by the wheel within the transfer sequence.

At the infeed, the pockets need to reach each container at the correct point in the cycle. On the way out, they need enough clearance to release the bottle without pulling it against the rail. Check these regions with the containers that will be used on the line. A bottle with a broad shoulder or a rectangular cross-section may contact a different part of the pocket than a round container with the same nominal width. A photograph of the bottle held between the star wheel and the rail can make that relationship visible before the geometry is finalized.

Illustrative bottle transfer on a packaging machine using the packaging star wheel

Illustrative rendering. Final geometry follows the approved drawing.

Pocket profile and bottle clearance

A wheel with a smooth semicircular pocket can fit a round bottle around a selected band of its body. With an oval or rectangular format, the entry radius and the direction of bottle rotation may be just as important as the seated shape. Mark the contact height on the container drawing and show nearby labels, embossed features, seams or handles if those features can touch the guide. A single outline taken at the widest point of a bottle can miss the contour at the height where the wheel actually runs.

Provide the expected spread of bottle dimensions, and explain which variations occur between packaging suppliers or production batches. A trial with a narrow sample may pass while a wider bottle has inadequate clearance at the entry. A wheel should also be checked with the intended adjacent rail in place. Clearance estimated from the wheel alone may not represent the space available around the container. Supply dimensioned views that show how the infeed guide and exit rail relate to the pocket as it turns.

Timing at the inlet and discharge

Identify the direction of rotation and the position occupied by a selected pocket when the machine indexes to its reference point. An upstream timing screw may set the spacing before a bottle reaches the wheel. In another installation, positioning may depend on a conveyor and stop arrangement. Show which equipment establishes the timing relationship. The wheel drawing can then place the pocket pattern relative to a real machine reference instead of relying on the nominal number of pockets.

Give the distance between the wheel axis and the centers of adjacent transfer elements or conveyors. Identify where the bottle enters and where an adjacent part begins to take control of it. At these transitions the path may be constrained by more than one surface, and adjustment to one rail can affect clearance in the next segment. If the container is handled empty at one station and full at another, include both cases in the planned fit check. Record any changes to the machine guides needed between formats.

Hub choices and changeover access

The wheel may mount through a keyed bore, a central flange or a quick-release hub supplied by the equipment maker. Use the shaft or hub drawing and state which surfaces carry the torque and which features control axial position. If there is an adapter between the molded body and the shaft, identify that adapter by revision. An assembly section showing the clamping hardware can reveal an interference that would be easy to miss when comparing two loose wheels.

A wheel used as a change part needs to be handled and reinstalled without losing the position used for approval. Show the reference orientation, the side that faces up, and any fastener or knob the technician must reach after the machine has been secured according to site procedures. Mark an appropriate location for the format identifier. If a label would be exposed to frequent cleaning, a customer may prefer a molded identification area away from the pockets and hub seat.

Illustrative bottle pocket and keyed hub on the packaging star wheel

Illustrative rendering. Final geometry follows the approved drawing.

POM selection for repeated bottle contact

Acetal is a candidate for repeated contact with containers and other moving packaging components. The appropriate grade depends on the bottle substrate, friction pair, required stiffness, washdown regime and ambient conditions. For a dry transfer line, start with the intended form and surface finish of the bottle. Where fluid or cleaning solution is present, provide the product, concentration and exposure conditions so the specific grade can be reviewed. A material designation on the order should identify the resin actually approved for the application.

Label scuffing and cosmetic marking should be checked using containers that carry the intended finish, sleeve or label. Clear bottles may show marks differently from opaque bottles even when their outside dimensions are similar. Inspect the wheel and the rail after a representative run and locate any repetitive contact on the machine drawing. A mark caused by one rail transition can look similar to a pocket problem when a bottle is inspected away from the line. Keep evidence of where each observation began.

Tool layout and finished profile

An injection molding review should cover the thickness around the hub and the pocket roots. Uneven sections can influence cooling and shape. A parting line positioned on the contact band can require different acceptance criteria from one in a recessed portion of the wheel. Indicate the surfaces where flash, an ejector witness or a gate mark could interfere with container transfer. If the wheel uses inserts or secondary finishing, identify those features on the finished component drawing.

Inspect the pocket pattern relative to the central mounting interface rather than using an arbitrary outer edge as the reference. An individual pocket can meet its local profile dimensions while the pattern is off-center after installation. An inspection report can include hub fit, relative pitch, the location of the contact band and runout where required. For a broad wheel, define how it is supported when measuring flatness or other geometry that may change when clamped in the machine.

Checking the first format set

Fit the approved wheel and guide set on the intended packaging line using the equipment builder's procedures. Begin by confirming shaft fit, installed height and clearance around all nearby components. Compare the bottle positions at the transitions and look for unintended contact before changing the operating setup. Once the equipment team confirms fit, a representative run can show whether a changeover part keeps its position and how containers behave at normal handling conditions.

Record the bottle revision, rail settings and wheel identification used for each trial. Where the wheel is expected to fit more than one format, evaluate every approved container instead of approving the whole family from one sample. Ask the receiving team to send a marked drawing or images of any contact or release issue. Include the point within the transfer sequence where it happens. That information helps determine whether the drawing, machine setup or adjacent hardware needs review.

Ordering a replacement or a new star wheel

For a replacement, submit the original component number and a model of the approved geometry when available. A used wheel can be useful for showing how it mounts, but worn pocket edges and worn keyways should be identified before measurements are used for tooling. Include an unworn sample or a nominal drawing if there is one. Provide the container range, machine station, direction of rotation, initial quantity and expected annual usage.

For a new project, identify the customer's equipment approval process and whether the supplier needs to make a single sample or a complete set of format parts. List the rail or hub items supplied separately and give the revision they must match. Provide a three-dimensional model with the dimensioned drawing and mark any geometry still open for review. SWKS can discuss molding and sample scope after the intended bottle, wheel and packaging equipment interfaces are defined.

Can one set of pockets serve several bottle formats?

Check the container outline at the actual transfer height and compare each format with the guide used to support it. If two bottles differ only above the contact band, the same pocket arrangement may be worth evaluating. A wider body, a changed neck position or a different guide can still make the formats behave differently at the inlet or exit. Record which combinations the machine builder has approved and give them separate identifiers where appropriate.

Bring a complete set of current format parts to a sample check where possible. In addition to the wheel and rail, include any clamp or insert that fixes their position. Give a marked photo of the approved operating setup and explain how the operator recognizes the correct wheel at changeover. A simple reference mark or a part label can help prevent mixing two wheels that use the same hub and similar pocket outlines.

Explore our custom plastic injection parts or read the SWKS guide to designing low-friction molded wear parts.

Request a quotation

Send the approved drawings, application details and estimated order quantities to amanda@tjswks.com or call 0086-15222707659.

Hot Tags: custom pom industrial packaging machine star wheel, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, automotive plastic injection parts, household plastic injection parts, injection molding plastic, Injection Molding Plastic Parts, Low Price PP Machine Parts, PC ABS Plastic Injection Molding Product

Send Inquiry

Send Inquiry