Custom POM Industrial Gear Pump Side Plate

Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial gear pump side plate in China. If you're going to buy bulk cheap custom pom industrial gear pump side plate, welcome to get quotation from our factory. Quality products and low price are available.

Custom POM Industrial Gear Pump Side Plate

The side plate in a gear pump is a small component with a direct influence on the internal assembly. Its face may locate beside the gears, while shaft openings, locating features and the housing establish its installed position. SWKS supplies custom POM industrial gear pump side plates for equipment builders who need a molded polymer component made to a controlled drawing.

The reference product is a compact plate with two shaft openings and corner fixing holes. The illustrated form is a design example; it does not define a pump rating or interchangeable replacement. The customer drawing specifies whether the plate acts as a wear surface, spacer, bearing support or combination of functions, and which features control the final fit.

Specification and Custom Manufacturing Scope

Material and Operating Conditions

POM can be considered for a mechanically loaded plate when its stiffness, dimensional behavior and sliding characteristics match the operating conditions. The exact resin grade must be selected with the pumped liquid, temperature, speed and lubrication in mind. A general acetal designation is insufficient to determine compatibility with a particular formulation, cleaning agent or additive package.

Share the liquid identity and concentration, possible contaminants, start-up conditions and periods of dry running. Chemical exposure and temperature may change the material response and installed clearances. If the pump uses a different polymer in an existing plate, provide that specification as a comparison point rather than assuming that visually similar plastics perform the same way.

Functional Geometry and Assembly

The two shaft centers should be dimensioned from functional datums that correspond to the housing. Plate thickness and face condition must be considered together with the gear stack and cover. A tolerance on an isolated hole does not describe the complete assembly: position, perpendicularity and distance to the working face can be equally relevant to the intended function.

When a relief groove or shaped recess is required, identify its purpose and boundaries on the drawing. An unspecified decorative groove should not be added to a functional sealing or wear surface. Gates and ejector locations need review so that the molding process does not place a raised mark where the part must sit flat or meet a moving component.

Application and Validation

Applications include custom fluid transfer modules, compact industrial gear pumps and equipment-specific pumping assemblies. The plate is supplied as a component within the customer design. Flow, pressure, leakage and endurance depend on the complete pump, its operating conditions and qualification results; these values cannot be established from a photograph of the side plate.

A sample assembly trial should confirm that shafts enter without forced alignment and that the plate seats against the intended support. Fastener tightening must follow the agreed assembly method. Excessive local clamping can distort a polymer plate, so a fixture that reproduces the real support condition is more informative than measuring the part under an arbitrary load.

Sampling, Inspection and Production Supply

First-article checks can cover overall thickness, bore diameters, center distance, fixing pattern and the nominated working face. Flatness inspection requires a stated support and measurement method. Where surface texture matters, define the target using an agreed specification or approved reference sample. Visual review should identify flash, short molding and damage around the shaft openings.

For a repeat order, drawing revision control is especially useful when housing or gear dimensions have changed. Retain the approved sample condition and any agreed assembly results. Packing should prevent hard components from marking the working face, while storage conditions should avoid loading the plate into a bent shape before it reaches the assembly line.

For further planning, see our guide to injection molding tolerances and functional fit. Identify critical interfaces and inspection datums before agreeing numerical tolerances, so that sample approval reflects the assembled function.

Request a Drawing-Based Quotation

Send the controlled drawing, 3D model, preferred material, required color and expected order quantity. Include mating-component details and the conditions the part will encounter in service. Mark the dimensions requiring a report and tell us which sample tests or material documents are needed for approval. Tooling scope, lead time and production requirements are confirmed after the project review.

Our guide to preparing a custom injection molding project explains the information used from CAD review through sampling. The product images show illustrative custom configurations; the approved drawing and material specification govern the supplied part.

Welcome to send an inquiry for your custom gear pump side plate. Contact amanda@tjswks.com or call 0086-15222707659 with your drawings and requirements.

Hot Tags: custom pom industrial gear pump side plate, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, ABS Enclosure Plastic Injection Molding Part Nylon Parts, ABS Injection Moulding Plastic Parts, ABS POM PP PE PU Plastic Motorcycle Parts, plastic injection molding parts, Polyurethane PU Coated Wheel Roller, transparent plastic injection parts