Custom PBT Industrial Circuit Breaker Trip Mechanism Lever

Material: ABS/POM/PA66/PP/PC/PA/PU/TPE/TPU etc.
Processing Service: Injection
Drawing Format: STP, STEP, IGS
Contact: amanda@tjswks.com / 0086-15222707659
Send Inquiry
Description

Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pbt industrial circuit breaker trip mechanism lever in China. If you're going to buy bulk cheap custom pbt industrial circuit breaker trip mechanism lever, welcome to get quotation from our factory. Quality products and low price are available.

 

Custom PBT Industrial Circuit Breaker Trip Mechanism Lever

SWKS develops custom injection molded PBT components for industrial equipment. This page outlines the application, drawing inputs and validation points for the circuit breaker trip lever. Share the operating conditions and assembly model so the material grade and molded features can be reviewed for your equipment.

An OEM Component for the Trip Mechanism

A circuit breaker may use a compact polymer lever within the mechanism assembly. This made to drawing part is one example of a molded PBT component for that application. The component has a pivot feature, a working end and a shaped body that connects the two. The locations and loads for those features depend on the specific device. A housing mount, a coil former and a trip lever occupy different positions in a switchgear assembly. The lever project begins with the breaker maker's released part drawing and identification of the corresponding mechanism revision.

A procurement drawing can separate dimensions that locate the part from outlines that simply keep it inside its allotted space. The bore or molded trunnion establishes the rotation axis. A point on the working end often needs a defined relationship to that axis. A stop or an adjacent case feature can add a further reference. Where the ends of the travel matter, the customer should identify those conditions on the assembly print and define what the component supplier needs to check. Use the same terminology in the purchase order, tool notes and sample reports.

the pivot and rocker body of the molded lever

Illustrative rendering of the pivot and rocker body of the molded lever. Production geometry follows the approved drawing.

Why the Pivot and Tip Are Reviewed Together

A pin can pass through a pivot hole while the lever still sits at a different angle from the intended reference. Bore profile, case location, side clearance and the tip outline each contribute to the position observed in the device. One way for the drawing owner to communicate the check is to show a dimension from the pivot axis to the specified point on the lever. Include a section indicating the plane of measurement. If a contact surface is curved, give the relevant contact direction or inspection fixture drawing so the result can be repeated between sites.

When the lever has distinct left and right forms, include both identifiers and the related housing layout in the order. Mixed lots of similar parts create problems at downstream assembly. The drawing owner may identify an unobtrusive feature for marking, provided it has clearance when the lever moves. Documentation can also use separate packaging labels and reference photographs. This is particularly helpful when two part revisions share a pivot diameter but have a different tip or stop. Keep a sample of each approved variant with its own reference identification.

PBT Grade and Approved Supply Conditions

Polybutylene terephthalate is a material family. A molding project can involve an unfilled PBT or a specified reinforced or modified PBT, with properties tied to the grade and formulation. The breaker manufacturer's controlled resin listing should identify which grade and color formulation the project uses. Confirm what material certificates or lot identifiers need to appear with shipments. When the acceptable design specifies the grade, that designation belongs on the molding approval paperwork along with any restrictions the equipment owner imposes on alternate sources or formulations.

A grade listing alone cannot establish the performance of an assembled breaker. The manufacturer remains responsible for the mechanism design, the device qualification program and release of the complete product. An order can call for component dimensions, surface condition and traceability alongside the sample quantities needed in that program. Information such as electrical requirements, test procedures and applicability by device revision comes from the OEM. This listing describes a custom component service. It makes no rating claim for any electrical device or operating environment.

Parting Line and Cavity Details Visible in a Small Part

The gate location matters where a mount or moving contact is close to the available feed area. Drawings can reserve different regions for gating and ejector marks and show where a sharp raised edge would affect nearby features. An undercut at the pivot may be handled differently from one on the outer body. Review tool access using the required section views, then identify any differing split line between the approved mockup and the production molding. The mold design can be reviewed against the mechanism at the same time as the lever drawing itself.

A thin arm attached to a thicker pivot region may have a different cooling history from the working end. Changes in geometry around a boss can affect whether the tip meets the height or angular position called out in the print. Inspect actual mold trials to see which dimensions move together. A report that relates the tip reading to the bore and cavity mark can help distinguish a trend from one isolated value. This is useful when discussing any approved tool correction with the device manufacturer.

Inspection From Loose Lever to Reviewed Assembly

Plan the component inspection around the lever's small functional surfaces. A quick check could begin with identifying the cavity and examining the bore and tip for excess flash under the agreed inspection conditions. Another check can compare measurements of the working end to a labeled drawing view. Use a defined fixture or contact location when positioning the component matters to the result. If a visual criterion is more practical than a dimension, include an approved representation of the location and what counts as an acceptable witness mark.

Inspection at the component level can be reported separately from an assembly trial commissioned by the breaker manufacturer. The OEM can prepare a reference mechanism and define which samples and product variants to put through its internal program. Preserve the receiving lot and the cavity identity with the results. A fit observation on one version gives a limited basis for changes to other versions. An approval record that distinguishes revisions and any measured setup condition makes it easier to request a later sample-run or reorder by released part number.

pivot bore and actuating tab

Illustrative rendering of pivot bore and actuating tab. Production geometry follows the approved drawing.

Storage and Packaging for Molded Rocker Arms

The pivot and working tip can be protected from direct loading or moisture and dirt during transport. The appropriate container depends on the lever outline and how it feeds the assembly station. Agree whether the project calls for bulk packaging with capped quantity per bag, a tray with individually supported positions, or another arrangement. Avoid identifying lookalike versions only by the loose parts inside the box. The outer package can show the buyer part number, manufacturing lot, grade code where required and quantity. An approved label sample avoids mismatches at goods receipt.

A small identification mark can be molded into a surface agreed during tooling review. In a limited envelope there may be little free area, so the drawing owner can choose whether the mark is on the part or carried by packaging. Information such as molding date or cavity can become valuable when checking if a single lot is affected by a later drawing or process question. Communicate which records must travel with the material and which the supplier is expected to archive. Purchasing can use the same identifiers on follow up orders and on the approval sample record.

Quoting a Mechanism Component Program

A useful quotation package includes a drawing and model of the lever, the matching breaker mechanism reference or a section of the operating region, the grade specification and production forecast. A first quotation can separate the mold budget and proposed sample milestones from recurring unit pricing. The product team can then decide how many cavities are appropriate and which qualification checks take place at which stage. Specify if every cavity needs separate reporting or if samples are needed with labeled positions in the mechanism.

If the existing lever is being replaced after an engineering review, include the date of the new revision and a summary of what changed. A complete photo of the assembly provides context, while a dimensioned view defines the contracted geometry. A worn example can be useful for understanding the area contacted by other mechanism parts. Its wear geometry should be interpreted against the OEM reference. Discuss whether a return sample, retained control part or component measurements should be supplied after the molding trial. Set the acceptance criteria for the lot and for later manufacturing changes before the production release.

Traceability for an OEM Mechanism Review

This part is offered as a made-to-drawing molding for the device manufacturer. The molded mechanical interface, grade identification and inspection report belong in the component record, while device level tests, certification and installation approval belong with the breaker manufacturer. Changes to formulation, pigments, suppliers or tool construction may require review even when the nominal outline is the same. The RFQ should name who owns the assembly drawing and how later engineering revisions are approved.

A drawing can distinguish the surface that locates the lever at the pivot from surfaces that simply clear the case. Use inspection photographs to show how the pivot and tip were measured. A contact surface can be called out for visual checks where flash or a raised edge is difficult to capture in a simple dimension. Provide the sampling level and reporting format before tool design, especially if measuring points require an agreed fixture or a defined approach direction. Identify any special packaging that protects tips and supports arms during transport.

Request a Drawing Review and Quotation

Browse our plastic injection parts and our injection molding design guide for related application information. Send your STP, STEP or IGS drawing, critical dimensions, operating conditions and target quantity to amanda@tjswks.com or call 0086-15222707659.

Hot Tags: custom pbt industrial circuit breaker trip mechanism lever, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, colored plastic injection parts, household plastic injection parts, Plastic Product Nylon Abs PP Molded Parts, polypropylene injection molding, PU Injection Molding Products, TPE compounds

Send Inquiry

Send Inquiry