Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial textile machine tension disc in China. If you're going to buy bulk cheap custom pom industrial textile machine tension disc, welcome to get quotation from our factory. Quality products and low price are available.
The POM Industrial Textile Machine Tension Disc is a molded thread-contact disc for a textile yarn tension assembly. SWKS develops the molded component to the customer's design. The product images are generated illustrations of a representative configuration. Contact amanda@tjswks.com for drawing review.
Design the Working Face Around the Yarn Path
A textile tension disc works against a facing disc or guide in an adjustable assembly. The yarn makes contact with the disc profile under a load set by the tension device. An unloaded photograph does not show where the yarn runs under production conditions. Mark the normal path through the device along with the entry and exit guides, the direction of threading and the space taken by the spindle or loading arm. Review the setup for each intended yarn range and note whether edge contact can occur as the package diameter or machine speed changes.
The contact radius, dish shape and small transitions near the rim influence the path. An abrupt ridge or poorly trimmed mark may catch yarn even when the outside diameter is acceptable. Put edge and contact-face requirements on the drawing where a visual inspection can support the dimensional checks. Compare a representative polished sample with the desired production texture. A finish selected for the face has a different job from a finish on the underside, which may simply seat against the carrier and should be dimensioned according to its own role.
Locate the Disc Along the Spindle

The central seat establishes the axial relationship between two loaded discs. Determine whether the part must slide along the spindle, rotate freely or remain fixed to a keyed support. A disc that tilts under load can contact the yarn differently at opposite sides of the assembly. Check the bore, face runout and support face as a group. Use the mating spring and a representative loading interface during early trials. If the assembly intentionally rotates one disc, describe that feature in the quotation request and show how the disc is prevented from wandering.
POM grade selection should consider the intended counterpart, the condition of the yarn surface and the expected cleaning routine. Lint and finish residue can change the observed response during service. Verify the molded candidate under the actual process before assuming that a low-friction material property alone will select the right disc. An unfilled material formulation and a wear-modified grade can produce different running behavior. Changing the resin can also change dimensions and a surface's appearance even when the mold geometry stays the same.

Compare Tension Through a Production Cycle
Thread a sample assembly using the usual machine method and observe whether the yarn follows the intended path. Run a low-speed setup check before collecting steady-speed data. A tension trace at agreed speeds or loading settings helps compare the new molded sample with the prior design. Include the required yarn sizes, finishes and start-stop conditions in the trial plan. Record whether the disc was newly fitted, cleaned or run in, as each condition can change how the surface behaves.
Quote Review and Replacement Parts
Send the disc section, spindle fit and contact-face requirements together. Provide the matching disc or a controlled section drawing when the quote is for one half of a paired assembly. Indicate the planned cleaning method and any requirement to install and remove the part without changing the machine setting. Keep an approved sample for receiving inspection and a matched set for line trials. If more than one contact geometry is needed, identify the machine and yarn range each will serve.
Sample Review and Manufacturing Requirements
The OEM can then carry out a tension trace and surface review after representative running time and routine cleaning. Where operating conditions vary, the useful validation set includes repeat use and samples that cover the functional tolerance range. Compare results against the agreed requirement rather than an impression from the prototype. Retain an approved assembly or representative parts to make later service and repeat-order investigations easier.
Suitable first-article checks include threading, low-speed startup and steady running trials using the target yarns and load settings. Document the result along with the cavity identity, drawing revision and resin. If a trial check fails, inspect the mating part and the way the sample was installed before changing a cavity. A single difficult assembly can be caused by incorrect orientation or a component at an extreme of its tolerance. A sample set and a clear note on what did not fit help make corrections specific.
Specify who will sign off the first samples and where the signed reference will be kept. In this case the reference should demonstrate contact profile, central bore, face runout and outer edge finish, along with access to a spindle, spring or loading element, matching disc and guides. If the mating items are supplied by another vendor, use the latest available production revision rather than a temporary prototype. Record any acceptable witness marks or edge finishes so a receiving inspector has the same expectations as the engineer who approved the sample.
Disc curvature and spacing influence the yarn path as the take-up station changes speed or the package diameter grows. The drawing should identify the reference used to establish this feature in the complete assembly. Confirm whether the reference is a plane, a molded profile or a dimension on a separately purchased item. A localized fit can be checked in the cavity during tool trials, then checked again as part of the assembled unit to see the effect of normal part-to-part variation.
For this part the review should cover intermittent starts, variable running speed and long exposure to sliding yarn. Note the highest expected condition and how often it occurs, along with fiber finish chemistry, lint accumulation and the approved cleaning routine. Report cases in which the part normally sits idle and is then used under a different condition. This helps distinguish a handling problem during assembly from a material or fit issue that appears after installation. Include exposure timing and any intended restriction on reusing removed parts.
Production Approval
An important drawing callout is a shallow dish with a continuous edge treatment around the working face. Identify which faces are visible, which locate or carry a load and which can accept ordinary molding witness marks. Review texture depth and draft together where the surface must release cleanly. Approve an appearance sample under the lighting in which the part will normally be seen or inspected, using the production resin and agreed process where possible.
Review the need for trial pieces taken at different points in the run when the application places particular emphasis on intermittent starts, variable running speed and long exposure to sliding yarn. The aim is an agreed method that procurement, engineering and receiving inspection can each follow. Report a change in resin, tooling location or mating hardware against the last approved revision when the change could affect the fit or operating duty.
When sending the RFQ, include the type and size range of yarn, mating disc and normal force range expected on the device. Include forecast volume, sample quantity and any resin documentation the purchasing team needs with the shipment. A 3D model shows the geometry. A revision-controlled two-dimensional drawing records the acceptance limits and reference surfaces. Identify a contact who can review questions about mating interfaces during mold preparation and initial sampling.
The part is made by injection molding to a customer-approved design. For the textile machine tension disc, the first review covers part orientation, shutoffs around openings and the location of the tooling split relative to the controlled features. Walls that blend gradually into supports generally make shrinkage easier to manage. Draft and radii should be allocated where there is room for them while preserving active contact surfaces and the expected approach direction of the mating parts.
POM is often considered where a molded moving component needs a repeatable sliding interface and low moisture pickup. Grade selection depends on the actual counterpart, temperature and duty rather than resin family alone. Both the material formulation and the way the part cools can influence the molded shape. Functional testing on the intended assembly is the place to compare wear, sticking or dimensional changes, especially when the part sees intermittent starts or running contact with another surface.
Order Details and Drawing Review
| Product | Custom POM Industrial Textile Machine Tension Disc |
| Process | Injection molding to the approved project drawing |
| Proposed material | POM in the grade agreed for the operating environment |
| Mating components | a spindle, spring or loading element, matching disc and guides |
| Critical drawing features | contact profile, central bore, face runout and outer edge finish |
| Sample checks | threading, low-speed startup and steady running trials using the target yarns and load settings |
| End equipment validation | a tension trace and surface review after representative running time and routine cleaning |
| Drawing package | STP, STEP or IGS model and controlled 2D drawing |
Keep the drawing and material decisions on one revision of the purchase record. Before authorizing the tool, agree which dimensions require a report and which checks rely on customer-supplied assembly parts. If the part is intended for more than one product revision, identify which versions the approved samples must fit.
See plastic injection parts and related SWKS design guidance. For pricing and samples, email your drawings and quantities to amanda@tjswks.com.
Hot Tags: custom pom industrial textile machine tension disc, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, China Nylon Sprockets Suppliers, complex plastic injection parts, Low Volume Injection Molding Machine, plastic parts for automotive industry, PP Plastic Parts For Plastic Special shaped Parts, standard plastic machinery components






