Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom abs industrial spectrometer sample carousel tray in China. If you're going to buy bulk cheap custom abs industrial spectrometer sample carousel tray, welcome to get quotation from our factory. Quality products and low price are available.
Custom ABS Industrial Spectrometer Sample Carousel Tray
The indexed optical sample carousel is a drawing-based ABS component for spectrometer sample handling. Map the active positions to the detector axis and include the home indication. The customer's assembly references define the limits of the molded supply. Drawings, resin grade and acceptance are project-specific. The generated photographs are illustrative concepts for quotation discussion.
Product specification
| Attribute | Drawing-based scope |
|---|---|
| Material | ABS grade to be confirmed |
| Process | Custom plastic injection molding |
| Application | spectrometer sample handling |
| Drawing package | STP, STEP or IGS plus dimensioned PDF |
| Quotation | Tooling, sample and order quantity reviewed by project |
Optical station and indexed pocket
Map the active positions to the detector axis and include the home indication. The dimension chain begins at the instrument shaft and ends at the face of a known sample holder. Mark the empty slot if it stays empty during calibration. In a comparison for spectrometer sample handling, ask the technician to fit a known approved counterpart before judging the new indexed optical sample carousel. The measurement is useful when it can be repeated with the unchanged datum and a clearly identified hardware set. When a key reference moves between models, record the actual value and indicate which part variation has been selected for the fit check.
When comparing a molded prototype to the intended equipment, map the active positions to the detector axis and include the home indication. The dimension chain begins at the instrument shaft and ends at the face of a known sample holder. Mark the empty slot if it stays empty during calibration.. Keep the trial results with the drawing, material grade and component revision. A surface that is acceptable on an individual sample may behave differently in a dimensional stack at the opposite limit. If a specific piece of hardware influences the observed condition, identify its drawing reference and whether alternate hardware is approved. Define the supplier's sample deliverable in terms of the visible and measurable requirements, then let the project owner determine whether a functional test of the complete equipment is needed.
Pocket seat and cell orientation
A sample holder can appear flush while sitting on the corner of a recess. Compare the actual foot and any corner key with the depth at multiple positions. The inner radius should not contact the optical window of a supported cup. During the shop review, compare the sample with the full model rather than an isolated dimension label. Photograph the pocket seat and cell orientation with an orientation mark so someone at incoming inspection can set up the same view. If a feature needs touch access, show the position of the tool or gauge with the neighboring assembly installed. Collect a retained reference that represents the accepted condition.
Review this requirement at the design stage: A sample holder can appear flush while sitting on the corner of a recess. Compare the actual foot and any corner key with the depth at multiple positions. The inner radius should not contact the optical window of a supported cup.. The working drawing for the indexed optical sample carousel should show its location in context. Record whether an installed result is controlled by the molding, by a separately supplied component or by their combined stack. When the drawing and assembly models come from different teams, specify which model revision governs the dimensional decision. This makes the agreed check reproducible at pilot approval and helps purchasing identify which parts or tooling updates need to be considered if an interface changes. Review what a supplier can measure directly and what needs a customer fixture.

Hub coupling and angular play
A shaft pin or flat can index the unit but carry separate loads during assembly. Identify where the tray stops axially and how the fixture detects side movement when the home arrow returns. Check the clockwise and reverse travel conditions specified by the instrument owner. The drawing package for spectrometer sample handling should state the change being proposed and identify the current comparison part. Review the difference in the assembled indexed optical sample carousel before focusing on isolated surface appearance. When the customer supplies a used part, identify wear and rework on the incoming specimen. A section and a dated drawing clarify which dimensions represent the new item, especially where service removed an edge.
A shaft pin or flat can index the unit but carry separate loads during assembly. Identify where the tray stops axially and how the fixture detects side movement when the home arrow returns. Check the clockwise and reverse travel conditions specified by the instrument owner.. Compare the CAD section with the real reference setup in spectrometer sample handling. A picture of a loose molded sample cannot show where an adjacent item occupies the same space in operation. A mounted view should identify the supports and distinguish the surfaces that locate the part from those that only need clearance. The customer can annotate inaccessible areas and give the intended order of assembly. Where two versions need different geometry, keep separate drawing labels and write down which mating references go with each. That distinction can affect both the tooling scope and sample review.
Reference clearance at the reading head
Use the instrument CAD to draw a keep-clear area around the optical head and any lifting fork. Include the holder and holder cap in that section. A carousel can match its outer envelope but still contact a holder at an intermediate angular position. Sample reports should identify where normal measurement touches the indexed optical sample carousel and where it could alter a sensitive face. Ask the fixture designer whether the proposed hold-down changes fit at the reference clearance at the reading head. If the review produces a repeated difference, check where the sample was restrained and verify whether the same behavior occurs in the actual owner-approved installation. Record the observations against the product revision.
A useful release check for indexed optical sample carousel starts with this requirement: Use the instrument CAD to draw a keep-clear area around the optical head and any lifting fork. Include the holder and holder cap in that section. A carousel can match its outer envelope but still contact a holder at an intermediate angular position.. Set out the relevant measurement and acceptance method using the released parts. Locate the surface or region under review rather than relying on overall dimensions. Mark the reference object in photos so that an inspection team can distinguish a loose fit check from the working installed condition. When a more accurate assessment calls for an assembled sample, include the intended hardware and state who will supply it. Agree what evidence is required to accept the prototype and how an approved change will be captured on the print.

Surface finish and sample handling
Distinguish dark molded surfaces around the cavities from engineered optical surfaces furnished separately. Review any glare or reading disturbance on the populated instrument. Quote sample labels and cavity marks only where they remain visible during normal handling. At ordering, keep any cosmetic reference and dimension report for the indexed optical sample carousel tied to the same approved configuration. Ask who supplies each mating item and which pieces accompany the order sample. The buyer can designate the ABS grade and any conditioning relevant to the surface finish and sample handling. Compare approved sample and production only using the conditions listed in the released purchase specification.
Distinguish dark molded surfaces around the cavities from engineered optical surfaces furnished separately. Review any glare or reading disturbance on the populated instrument. Quote sample labels and cavity marks only where they remain visible during normal handling.. Make a list of the fitting states that affect the indexed optical sample carousel, including any condition the machine owner identifies as important during maintenance. A physical reference can expose simple restrictions overlooked in an isolated component model, such as an approach direction blocked by the surrounding system. A useful pilot report labels the machine version, the approved configuration and the measurement setup. When a fit problem appears, note the exact position rather than asking for a change to the entire external envelope. The finding can then be checked against the specification before changing the tool.
Instrument trial and spare selection
Check sequential placement with representative holders, then change the loading arrangement if that is normal service. Report the physical location of a repeated anomaly and track whether it follows the cup or the pocket. Keep the hub revision with retained samples. Make the instrument trial and spare selection visually identifiable in a section through the indexed optical sample carousel. Use one callout for the surface supplied by SWKS and another for the mating hardware kept by the equipment manufacturer. Which witness is easiest to see will depend on the installed orientation. Include the same reference in the first-article checklist so inspection can address the intended feature.
For spectrometer sample handling, the purchaser should clarify this interface early: Check sequential placement with representative holders, then change the loading arrangement if that is normal service. Report the physical location of a repeated anomaly and track whether it follows the cup or the pocket. Keep the hub revision with retained samples.. Information beyond the 3D surface model can include a force limit, an accepted reference sample, a grade requirement or a specific installation arrangement. Identify restrictions on changing critical features for moldability. Other details may be negotiable if they do not affect the component's function. Preserve the resulting decisions in a dated record so that the toolmaker and incoming inspection use the same revision. Discuss the tolerance condition before measuring early parts and include any relevant conditioning or inspection fixture in that discussion.
Sample approval and purchasing
Related components: Custom PC Industrial Laboratory Analyzer Sample Tray and Custom ABS Industrial Laboratory Centrifuge Rotor Adapter.
Send your drawings and quantities to amanda@tjswks.com for a project quotation.
Hot Tags: custom abs industrial spectrometer sample carousel tray, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, Customized OEM ODM Nylon Plastic Parts, Nylon PU Coated Wheel Bushings PA, PC ABS Plastic Injection Molding Product, Plastic Speaker Casing Housing Cover Shell, PP Hard Injection Automotive Plastic, PP Injection Molded Polypropylene Machine Plastic Parts






