Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pa66 industrial textile machine heddle frame in China. If you're going to buy bulk cheap custom pa66 industrial textile machine heddle frame, welcome to get quotation from our factory. Quality products and low price are available.
Custom PA66 Industrial Textile Machine Heddle Frame
A molded heddle-frame component supports customer-defined rail and mounting interfaces inside a weaving assembly. The illustration shows a compact open frame concept. The final envelope, heddles and drive hardware are supplied as engineering references. Pictures are generated examples for project discussion. All finished dimensions, material specification and qualification requirements depend on the approved design.
Set out the loom station before sizing the mold
A heddle frame works within a stack of moving frames, so the drawing package starts with the space assigned to one position in the loom. Show the nominal position of the frame and the occupied volume of the frames on both sides. A small shoulder on a mounting foot can sit outside the clearance available during travel even if the part fits a layout checked at rest. Keep the approved loom arrangement with the quotation so the mold proposal refers to the correct machine width and station.
Product specification
| Material | PA66 |
| Manufacturing method | Custom injection molding |
| Application | loom and weaving shed assemblies |
| Assembly references | upper and lower rails, heddles, lifting connections, guides and adjacent frames |
| Drawing formats | STP, STEP, IGS and a dimensioned print |
| Validation scope | rail fit, heddle movement, side clearance and equipment-owner validation under the approved weaving cycle |
For this item the drawing package should give the complete context. Specifically, measure the distance and parallelism between the supported rails. The best section is one that shows the feature in its intended assembled state. Include hardware type and any permitted alternate part. If access or fit changes with the alternate, quote an agreed revision first and review the second configuration before sharing a tooling decision. Keep the part data for loom and weaving shed assemblies tied to its intended revision.
Relate the two rail seats
Heddles and their carriers establish which section of the rail needs to be supported. Mark the upper and lower rail seats and the plane used to check their position. Dimensioning the rails from a common plane can help expose a change in parallelism that would be easy to miss if each rail seat is measured alone. Provide the intended metal rail and heddle models because a molded perimeter frame can leave room for both parts while their assembled retention still needs review.

At sample approval, identify the fasteners and how the lifting rods pull on the molded structure. The part manufacturer and the purchaser can then review the same configuration. Retain the reference setup, including the way the component is supported and the selected mating items. A difference between an unmounted measurement and an assembled one should be documented with the condition and measuring point. This avoids deciding whether a sample is usable based only on the shape visible in a photograph of molded heddle-frame component.
Account for lifting and guide hardware
Include the lifting attachments, guide surfaces and any separate hardware passing through the frame. Identify which areas react drive loads, which contain loose clearance and which simply cover a portion of the loom. Specify the direction of the applied motion, how the part is seated and the range supplied by the manufacturer. If the frame uses multiple mounting options, keep each variant identified instead of allowing a common hole pattern to imply compatibility. The equipment owner validates the lift mechanism and installed frame under the intended weaving cycle.
Use a controlled sample to record the slot or rail shape where the heddles are carried. Before agreeing on a manufacturing tolerance, identify which areas can use ordinary process variation and which need a specifically documented result. The priority should be the features related to installation, the agreed service role and the checks in the equipment drawing. Label the revision of the molding and mating components if any decision is made during a pilot run for loom and weaving shed assemblies.
Evaluate movement with the real heddles fitted
Use the loom drawing and a populated reference assembly to check the available space for the heddles in all approved positions. Compare multiple frames together. The part under review may share a mounting approach with a previous revision while its rail seats sit in a different plane. Check how an operator accesses a rail retainer and how the heddles are removed for maintenance. Preserve that maintenance space when considering local draft, ribs and attachment features. Identify where the customer has specified wearing or sliding surfaces and include the matching materials.

On the quotation review, check the frame motion with a populated neighboring frame and the machine maker's permitted travel. Add an acceptance method to the drawing when the requirement cannot be understood from the model alone. Explain whether the initial check requires a fixture, a reference assembly or a representative installed component. If an inspection report is requested, agree on the fields that must appear in the report before ordering pilot parts. This helps keep the assessment of molded heddle-frame component separate from qualification of the complete equipment.
Review humidity, fiber and finish
Share the loom environment and cleaning or lubrication practices. Nylon conditioning belongs in the sample inspection record when the agreed dimensions depend on it. If loose fibers collect in a particular part of the machine, include the location and trace the clearance around the occupied rail path. Document any requirements for the molding surface near the heddles. A surface witness permitted on an outer face might interfere at a sliding support, so agree on where trimming is acceptable.
During a review of molded heddle-frame component, ask the owner to provide lubricant or fiber residue and the cleaning schedule. Treat this as a controlled interface rather than an appearance preference. A model supplied alone may have enough information for a rough quotation while omitting the references needed to confirm assembly. For an engineering review of loom and weaving shed assemblies, mark the relevant surfaces on both the customer assembly and the part drawing. Indicate which dimensions are checked before assembly and which depend on the selected mating items.
Approve a representative frame rather than a disconnected insert
Inspect the rail relationship before fitting the prototype on the authorized test fixture, then compare populated clearances using the approved loom sequence. Communicate any visible shift at a lifting connection, local rubbing or obstruction by marking the affected position. If changes are made to the part, keep the approved station, frame revision and mating rail in the record. A well-identified reference can prevent a later order from reverting to rail geometry that was superseded during first articles. The image illustrates a compact molded concept; long or load-bearing frame applications require a project-specific feasibility and qualification review.
Ask the design team to identify the loom station and compare the whole frame outline rather than sharing one rail measurement. A useful review separates the manufactured component from the extra space needed to install it. Record the position and any access requirement after nearby hardware is fitted. When different equipment revisions share an outer shape, include a separate view of each arrangement. This gives purchasing a clear way to trace a request for molded heddle-frame component to the assembly that actually needs it.
Purchase and sample approval
Before releasing parts for a pilot build, list the checks that must be performed by the customer and those the molding shop should report. A straight edge, go gauge, fit template or fixture can serve different purposes. Describe the intended acceptance process and the exact inspection condition. Product photographs help explain the application without replacing a sample report or the equipment owner's operating limits.
In a new sourcing project, identify which requirements are frozen and which are still in development. Specify timing for samples separately from a request for routine batches. If the molding is meant for several options, provide a clear configuration matrix instead of mixing dimensions from several versions in one drawing. Confirm how the customer will approve any updates before an order for production is released.
Fiber and oil in the project record
On the quotation review, provide lubricant or fiber residue and the cleaning schedule. Add an acceptance method to the drawing when the requirement cannot be understood from the model alone. Explain whether the initial check requires a fixture, a reference assembly or a representative installed component. If an inspection report is requested, agree on the fields that must appear in the report before ordering pilot parts. This helps keep the assessment of molded heddle-frame component separate from qualification of the complete equipment.
Station matching in the project record
During a review of molded heddle-frame component, ask the owner to identify the loom station and compare the whole frame outline rather than sharing one rail measurement. Treat this as a controlled interface rather than an appearance preference. A model supplied alone may have enough information for a rough quotation while omitting the references needed to confirm assembly. For an engineering review of loom and weaving shed assemblies, mark the relevant surfaces on both the customer assembly and the part drawing. Indicate which dimensions are checked before assembly and which depend on the selected mating items.
Rail separation in the project record
Ask the design team to measure the distance and parallelism between the supported rails. A useful review separates the manufactured component from the extra space needed to install it. Record the position and any access requirement after nearby hardware is fitted. When different equipment revisions share an outer shape, include a separate view of each arrangement. This gives purchasing a clear way to trace a request for molded heddle-frame component to the assembly that actually needs it.
Related SWKS products include Custom POM Industrial Textile Machine Shuttle Guide and Custom POM Industrial Textile Machine Yarn Feeder Gear.
For a drawing-based quotation, send the assembly references and required quantity to amanda@tjswks.com.
Hot Tags: custom pa66 industrial textile machine heddle frame, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, Custom High Temperature TPE Plastic Machine Parts Product, High Temperature TPE Plastic Injection Parts, Nylon ABS Plastic Injection Molded, plastic rubber machinery parts, polypropylene plastic, Prototype Injection Molded Parts






