Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial textile machine yarn feeder gear in China. If you're going to buy bulk cheap custom pom industrial textile machine yarn feeder gear, welcome to get quotation from our factory. Quality products and low price are available.
Custom POM Industrial Textile Machine Yarn Feeder Gear
This custom POM gear transmits motion within a textile yarn feeder assembly. It is designed around the feeding mechanism's shaft and gear mesh. The illustrated spur gear is a representative shape, with tooth count and precise profile to be defined by the approved print. The photographs are generated examples for drawing review. Production geometry is confirmed through the approved project drawing.
Treat the yarn feeder as a geared assembly
A yarn feeder gear transmits rotation to the feeding mechanism. It can be located inside a housing with no direct yarn contact. Begin with the mating pinion, the feeder shaft and its bearing positions. Provide the installed center distance and the drawing revision of the mating gear. A feeder may have more than one speed ratio available for different yarn lines, so confirm which ratio is required and how the different gears will be distinguished in service. Tooth count, module and profile should be specified on the buyer's drawing rather than inferred from the reference photographs.
Show the way the gear is located axially. A shoulder, E-clip, spacer or other retaining feature may place the hub face relative to the bearing or pinion. Include the shaft lengths and fit requirements from the locked assembly. Where the part is chosen to replace a worn sample, first confirm which dimensions on that sample remain representative. A damaged tooth or a worn bore is an unreliable master. A dimensioned drawing can preserve the intended fit even after the original part is no longer available.
Manufacturing scope
| Material | POM |
| Process | Custom injection molding |
| Application | industrial textile yarn feed stations, winding machines and feeder assemblies |
| Mating components | mating gear, keyed shaft, support bearings and feed roller drive components |
| Drawing formats | STP, STEP, IGS and dimensioned drawing |
| Inspection and validation | tooth profile, centered rotation, assembly backlash and a representative running test |
Specify the active tooth and shaft interfaces
Put the basic tooth geometry in the quotation package and state how tooth accuracy will be checked. Inspect the relationship between the gear teeth and the hub bore, because both affect mesh as the part rotates. Confirm working backlash on the actual center distance. A mesh that is overly tight in one angular position deserves an inspection of the combined shaft, hub and tooth form before changing the tooth geometry. A loose mesh with noise at startup may also point to retention or the mating drive rather than the material alone.
A keyway, flat or shaped bore can transfer torque, while the hub face or clip establishes the axial position. Identify the installation direction and the usable key engagement. Document whether a separately installed hub or insert is included. Draw any shoulder that must clear a bearing seal or support plate. If the current feeder uses an interchangeable shaft, confirm the rotation direction and which end of the gear faces the drive. A simple orientation note can prevent the pilot assembly from being tested with the part reversed.

Discuss the feeder duty with the customer
Some lines run steadily while others start and stop when the equipment changes yarn, stops for inspection or corrects tension. Ask for the relevant speed range, start frequency and expected drive load. Establish whether the gear is installed dry or lubricated and what material is used for the opposing teeth. Include fiber and dust exposure if the gear is not enclosed. If a drive sits near a heated enclosure or motor, share the expected local operating temperature rather than the ambient building temperature alone.
POM grade selection should reflect tooth geometry, mesh material, lubrication and the fit of the shaft interface. A proposed grade change needs review alongside dimensional targets and the equipment trial. Include any color signal used to identify the correct ratio. If two known gear versions look alike, agree how a buyer or technician can tell them apart during maintenance. Part identification must not remove useful material from a functional tooth or bearing contact area.
Plan cavity and first article checks
Identify the surfaces that should stay free of a gate vestige or trim mark. A gate position that is convenient on the hub may leave a witness on the face that controls axial position. Agree where the mark is acceptable. Specify how tooth form, dimensional checks and fit samples will relate to each produced cavity. If a later production release requires measurement records, use consistent tooth and bore datums so the first articles can serve as a meaningful reference.
Run the accepted samples in the representative yarn feeder with the intended mate. Record speed, loaded condition, running sound and any change in feed behavior that matters to the equipment designer. Check that the assembly returns to its intended condition after a planned stop and restart. Inspect the gear and mate after the run. If the measured feed changes, document whether the observation began at acceleration, at steady running or after the line warmed. Identify the machine and yarn setup used in the test record.
Information to include with an inquiry
Send the gear model, dimensioned tooth requirements, mating part reference, shaft model and target sample and production quantities. Label any alternate ratios and include the versions used on the planned feeder. State whether the order is for one resin grade or whether material options are to be reviewed. Keep the machine trial requirements with the quotation so the scope for fit and running evaluation is clear.
Distinguish the feed head from the take-up unit
A textile machine may use a production take-up roller after the yarn has passed through several processes. The feed head has a different task at the start of the yarn path. It supplies yarn to the point where the next operation needs it. In a feed head with a geared roller, the gear and the correct mating member should be identified using the feed head assembly number. On a machine that has many similar stations, compare tooth counts on the station that is being repaired before releasing purchase quantities. Samples from a take-up station can resemble those from a feed station while using a different hub and installed position.

With the feed head open and unpowered, document the approach used by the technician to install or remove the gear. Look at the guard, the route taken by the yarn and any tool required to reach a clip. If access is blocked by adjacent heads, it may be necessary to remove a subassembly before replacing the gear. Record the version of the feed station and the expected replacement sequence. Quoting from a loose gear without the model identity can send an otherwise usable part to the wrong station.
Use the yarn path to design a meaningful trial
Collect baseline observations for the yarn being run on the target head. Agree whether the useful acceptance value is delivered length for a defined number of drive turns, regularity during a steady run, the repeatability of starts, or a criterion chosen by the machine owner. An initially stable reading with a loosely loaded guide does not show how a worn or incorrectly seated roller behaves at the actual working setting. Keep the yarn route and feeder setting constant when comparing two sample gears. Change one condition at a time so the engineer can tell which adjustment accounts for a change in the result.
If the line has recipe changes, note the sequence used to change yarn and restore the head to its working state. A trial could compare the first run after threading with the same head after a period of steady operation. Locate observations by station and machine side if several heads are compared. If users see local lint buildup, inspect the gears and the surrounding guide path separately. Lint collected on a cover tells little about actual contact at a particular gear tooth. The owner's test plan can distinguish a gear-interface problem from an issue created by the path over the guides.
Check low speed and changeover behavior
Run the head slowly under the owner's commissioning procedure before moving to the agreed operating point. If the line is indexed, include a sequence of ordinary pauses and restarts to observe how a head returns to feed. Record observations with the gear, shaft and selected yarn identified. A running sound or repeating fluctuation may be easier to locate when it is tied to the same point in the drive cycle. Compare it with the timing and the yarn motion, then make a separate inspection of the gear and the roller surface before assigning a cause.
Label spare gears for maintenance
Keep the replacement part number and feeder head identification with the incoming inspection sheet. A buyer who carries two gear ratios may need to separate packaging at receipt as well as on the parts rack. Specify what an individual bag or carton must identify and decide whether an example of an accepted gear can be retained at maintenance. Include the quantity of each revision to be stocked and note which versions are interchangeable only if the equipment owner has confirmed that fact. An updated hub or keyway may require different service documentation even when the tooth count has not changed.
If an old feeder runs several grades of yarn, send the grade or size range relevant to the intended gear trial. Include the location of any textile oil or antistatic treatment in the line. These notes help define realistic test conditions and clarify that yarn handling is evaluated on the assembled head. Photos and dimensions can guide the inquiry, while the approved gear drawing determines the molded geometry.
See our plastic injection parts and Custom POM Industrial Textile Machine Tension Disc.
Send your drawing and request a quotation at amanda@tjswks.com.
Hot Tags: custom pom industrial textile machine yarn feeder gear, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, Custom Plastic Abs Pp Pc Injection Molding Part, PA66 Plastic Special-shaped Parts Injection Molding Parts, pc parts, polypropylene injection molding, Polyurethane Coated Rubber Urethane Rollers, small plastic injection parts






