Injection molding, also known as injection molding, is a molding method that combines injection and molding. The advantages of the injection molding method are fast production speed and high efficiency, the operation can be automated, there are many designs and colors, the shapes can be from simple to complex, and the sizes can be from large to small, and the product dimensions are accurate, the products are easy to replace, and can be made into complex shapes Parts, injection molding is suitable for mass production and complex-shaped products and other molding processing fields.
At a certain temperature, a completely molten plastic material is stirred by a screw, injected into the mold cavity with high pressure, and cooled and solidified to obtain a molded product. This method is suitable for mass production of components with complex shapes and is one of the important processing methods.
- Basic Information of Injection molding
- History
- Injection molding process
- Pressure control
- Injection pressure
- Parameter
- Basic Information of Injection molding
The injection molding process can be roughly divided into the following 6 stages:
Mold clamping, glue injection, pressure maintaining, cooling, mold opening, and product removal.
By repeating the above process, products can be produced periodically in batches. The molding of thermosetting plastics and rubber also involves the same process, but the barrel temperature is lower than that of thermoplastic plastics, and the injection pressure is higher. The mold is heated. After the material is injected, it needs to go through a curing or vulcanization process in the mold, and then is defilmed while it is hot.
The trend of today's processing technology is developing in the direction of high-tech. These technologies include: micro-injection molding, high-fill composite injection molding, water-assisted injection molding, mixed use of various special injection molding processes, foam injection molding, mold technology, simulation technology, etc.
In 1868, Hyatt developed a plastic material he named celluloid. Celluloid had been invented in 1851 by Alexander Parks. Hyatt improves it so that it can be processed into finished shapes. Hyatt and his brother Isaiah registered the patent for the first plunger injection machine in 1872. This machine is relatively simpler than those used in the 20th century. It operates basically like a giant hypodermic needle. This giant needle (diffusion barrel) injects plastic into the mold through a heated cylinder.
In the 1940s World War II created a huge demand for cheap, mass-produced products. , low-priced, mass-produced products.
In 1946, American inventor James Watson Hendry built the first injection molding machine, which allowed for more precise control of injection speed and quality of produced items. This machine also enables material mixing before injection, so that colored or recycled plastics can be thoroughly mixed into virgin matter. In 1951, the United States developed the first screw injection machine. It did not apply for a patent, and this device is still in use.
In the 1970s, Hendry went on to develop the first gas-assisted injection molding process and allowed the production of complex, hollow products that cooled rapidly. This greatly increases design flexibility as well as the strength and endpoints of manufactured parts while reducing production time, cost, weight and waste.

temperature control
- Barrel temperature: The temperatures that need to be controlled during the injection molding process include barrel temperature, nozzle temperature and mold temperature, etc. The first two temperatures mainly affect the plasticization and flow of plastics, while the latter temperature mainly affects the flow and cooling of plastics. Each plastic has a different flow temperature. The same plastic has different flow temperatures and decomposition temperatures due to different sources or grades. This is due to different average molecular weights and molecular weight distributions. Plastics in different types of injection molding have different flow temperatures and decomposition temperatures. The plasticizing process in the machine is also different, so the temperature of the barrel is also different.
- Nozzle temperature: The nozzle temperature is usually slightly lower than the maximum temperature of the barrel. This is to prevent the "salivation" that may occur in the straight-through nozzle. The nozzle temperature cannot be too low, otherwise it will cause premature solidification of the molten material and block the nozzle, or the premature solidification material will be injected into the mold cavity and affect the performance of the product.
- Mold temperature: Mold temperature has a great influence on the intrinsic performance and apparent quality of the product. The mold temperature depends on the crystallinity of the plastic, the size and structure of the product, performance requirements, and other process conditions (melt temperature, injection speed and pressure, molding cycle, etc.).
Pressure control
The pressure during the injection molding process includes plasticizing pressure and injection pressure, and directly affects the plasticization of plastic and product quality.
- Plasticizing pressure: (back pressure) When using a screw injection machine, the pressure exerted by the melt at the top of the screw when the screw rotates and retreats is called plasticizing pressure, also known as back pressure. The size of this pressure can be adjusted through the relief valve in the hydraulic system. In injection, the size of the plasticizing pressure needs to be changed depending on the screw design, product quality requirements and the type of plastic. If these conditions and the screw speed remain unchanged, increasing the plasticizing pressure will strengthen the shear. The effect is to increase the temperature of the melt, but it will reduce the efficiency of plasticization, increase counterflow and leakage, and increase driving power.
In addition, increasing the plasticizing pressure can often make the temperature of the melt uniform, the color materials can be mixed evenly, and the gas in the melt can be discharged. In general operations, the plasticizing pressure should be determined as low as possible while ensuring excellent product quality. The specific value varies with the type of plastic used, but it usually rarely exceeds 20 kg/cm2.
Injection pressure: In current production, the injection pressure of almost all injection machines is based on the pressure of the plunger or the top of the screw against the plastic.
The applied pressure (converted from the oil line pressure) shall prevail. The role of injection pressure in injection molding is to overcome the flow resistance of the plastic from the barrel to the cavity, give the molten material a filling rate and compact the molten material.
- Molding cycle
The time required to complete an injection molding process is called the molding cycle, also known as the molding cycle. It actually includes the following parts: Molding cycle: Molding cycle directly affects labor productivity and equipment utilization. Therefore, during the production process, the relevant times in the molding cycle should be shortened as much as possible while ensuring quality. In the entire molding cycle, injection time and cooling time are the most important, and they have a decisive impact on the quality of the product. The filling time in the injection time is directly inversely proportional to the filling rate. The filling time in production is generally about 3-5 seconds. The holding time in the injection time is the pressure time on the plastic in the cavity, which accounts for a large proportion of the entire injection time, generally about 20-120 seconds (up to 5-10 minutes for extra thick parts). The holding time before the melt is frozen at the gate will have an impact on the dimensional accuracy of the product. If it is later, it will have no impact. The holding time also has a best value, which is known to depend on the material temperature, mold temperature and the size of the main channel and gate. If the dimensions of the main channel and gate and the process conditions are normal, the pressure value with the smallest fluctuation range of the shrinkage rate of the product is usually used. The cooling time mainly depends on the thickness of the product, the thermal and crystallization properties of the plastic, and the mold temperature. The end point of the cooling time should be based on the principle of ensuring that no changes are caused when the product is demolded. The cooling time is generally between 30 and 120 seconds. It is not necessary for the cooling time to be too long. It will not only reduce the production efficiency, but also affect the quality of complex parts. It will cause difficulty in demoulding, and even demoulding stress will occur when forced demoulding. Other times in the molding cycle are related to whether the production process is continuous and automated and the degree of continuity and automation.

- Injection pressure
Injection molding pressure is provided by the hydraulic system of the injection molding system. The pressure of the hydraulic cylinder is transmitted to the plastic melt through the screw of the injection molding machine. Driven by the pressure, the plastic melt enters the vertical flow channel (also the main flow channel for some molds), main flow channel, and shunt flow of the mold through the nozzle of the injection molding machine. channel, and enters the mold cavity through the gate. This process is the injection molding process, or called the filling process. The existence of pressure is to overcome the resistance during the melt flow process, or conversely, the resistance existing during the flow process needs to be offset by the pressure of the injection molding machine to ensure that the filling process proceeds smoothly.
During the injection molding process, the pressure at the nozzle of the injection molding machine is the highest to overcome the flow resistance of the melt throughout the process. Thereafter, the pressure gradually decreases along the flow length toward the front wave front of the melt. If the exhaust inside the mold cavity is good, the final pressure at the front end of the melt is atmospheric pressure.
There are many factors that affect the melt filling pressure, which can be summarized into three categories: (1) material factors, such as the type and viscosity of the plastic, etc.; (2) structural factors, such as the type, number and location of the pouring system, the shape of the mold cavity and the quality of the product. Thickness, etc.; (3) Process factors of molding.
2.Injection molding time
The injection molding time mentioned here refers to the time required for the plastic melt to fill the cavity, excluding auxiliary time such as mold opening and closing. Although the injection time is very short and has little impact on the molding cycle, the adjustment of the injection time has a great effect on the pressure control of the gate, runner and cavity. Reasonable injection molding time helps the melt to be filled ideally, and is of great significance for improving the surface quality of the product and reducing dimensional tolerances.
The injection molding time is much lower than the cooling time, about 1/10 to 1/15 of the cooling time. This rule can be used as a basis for predicting the entire molding time of plastic parts. When doing mold flow analysis, only when the melt is completely driven by screw rotation to fill the cavity, the injection time in the analysis results will be equal to the injection time set in the process conditions. If the screw pressure switching occurs before the cavity is filled, the analysis results will be greater than the setting of the process conditions.
3.Injection molding temperature
Injection molding temperature is an important factor affecting injection molding pressure. The barrel of the injection molding machine has 5 to 6 heating sections, and each raw material has its own suitable processing temperature (for detailed processing temperatures, please refer to the data provided by the material supplier). Injection molding temperature must be controlled within a certain range. If the temperature is too low, the melt will be poorly plasticized, affecting the quality of the molded parts and increasing the difficulty of the process; if the temperature is too high, the raw materials will easily decompose. In the actual injection molding process, the injection temperature is often higher than the barrel temperature. The higher value is related to the injection rate and material properties, and can reach up to 30°C. This is due to the fact that the molten material is sheared when passing through the injection port and generates high heat. There are two ways to compensate for this difference when doing mold flow analysis. One is to try to measure the temperature of the molten material when it is injected into the air, and the other is to include the nozzle when modeling.
4.Holding pressure and time
Near the end of the injection molding process, the screw stops rotating and just pushes forward. At this time, the injection molding enters the pressure maintaining stage. During the pressure-holding process, the nozzle of the injection molding machine continuously replenishes material into the cavity to fill the volume vacated due to the shrinkage of the part. If no pressure is maintained after the cavity is filled, the part will shrink by about 25%, especially the ribs that will shrink too much and cause shrinkage marks. The holding pressure is generally about 85% of the maximum filling pressure, which of course should be determined based on the actual situation.
5.Back pressure
Back pressure refers to the pressure that needs to be overcome when the screw reverses and retreats to store material. Using high back pressure is beneficial to the dispersion of color materials and melting of plastics, but it also prolongs the screw retraction time, reduces the length of plastic fibers, and increases the pressure of the injection molding machine. Therefore, the back pressure should be lower, generally no more than that of injection molding. 20% of the pressure. When injecting foam plastic, the back pressure should be higher than the pressure formed by the gas, otherwise the screw will be pushed out of the barrel. Some injection molding machines can program back pressure to compensate for the reduction in screw length during melting, which reduces heat input and causes the temperature to drop. However, since the results of this change are difficult to estimate, it is not easy to make corresponding adjustments to the machine.


