Tianjin SWKS Technology & Development Co.,Ltd is one of the most reliable manufacturers and suppliers of custom pom industrial automation pallet lift locator in China. If you're going to buy bulk cheap custom pom industrial automation pallet lift locator, welcome to get quotation from our factory. Quality products and low price are available.
Custom POM Industrial Automation Pallet Lift Locator
An injection-molded POM locator for repeatable pallet registration on industrial automation lift stations.
| Part material | POM |
|---|---|
| Other materials for custom parts | ABS, POM, PA66, PP, PC, PA, PU, TPE, TPU |
| Processing | Injection molding |
| Drawing formats | STP, STEP, IGS |
| Configuration | Custom part manufactured to the approved product drawing |
Pallet registration during lift transfer
A pallet lift locator helps bring a pallet or fixture into a defined position at an automation station. The part may guide a pocket into alignment as the lift rises, then provide a repeatable mating surface once the station is seated. The equipment layout should identify the direction of approach, the pallet geometry and the role of other stops, guides and sensors. Show which components establish final location and which take the supported weight in the assembled equipment.

Illustrative rendering. Final part geometry follows the approved drawing.
Lead-in and contact geometry
The tapered approach should match the expected offset and the direction from which the pallet arrives. Document the envelope of pallet position before it contacts the locator and define the final datum. A longer taper may need more available travel. A short lead-in may require closer upstream alignment. Show the shape of the matching pallet feature, including edge radii and any wear insert. Define the surfaces used to check seating height and final lateral position.
POM grade and sliding interface
POM can be considered for wear surfaces and guides in industrial automation. Supply the counterface material and finish, expected cycle frequency, relevant loads and cleaning conditions. A steel pallet receiver and a molded plastic pocket can pose different wear requirements for the locator. Check the required grade, dimensional conditions and allowable wear as part of the assembly review. If grease, debris or abrasive particles are expected near the mating surface, show where they may accumulate during repeated operation.
Fastening and service access
Show the positions of mounting screws, locating pins and any shoulder that fixes the position of the locator on the lift carriage. Fasteners should have the specified seating and enough access for adjustment or replacement under the maintenance procedure. When the locator is part of a matched pair, define which references establish the spacing between parts. Check whether a replacement can be installed against the same references without changing the equipment setup.

Illustrative rendering. Final part geometry follows the approved drawing.
First article and machine trial
Inspect the locating profile and mounting interfaces relative to the datums identified on the approved drawing. Try the sample with representative pallets across the intended fit range, using the equipment builder's procedures. Check approach, full seating and release. Observe where the wear marks appear after repeated motion and record whether the final station position stays within the specified limits. A report with the sample revision and pallet versions gives context to any adjustment requested after the trial.
Transferring location between stations
Where a pallet is carried by a conveyor before being lifted, the conveyor rails, carriage and locator may each establish a different positional reference. A machine drawing should distinguish the point at which the pallet leaves its transport supports from the point where it is registered for processing. Identify the distance available between initial contact and final seating. If other guides engage first, show their locations and the permitted clearance throughout the approach.
A pallet family may include fixtures of different mass and footprint. Indicate whether the same receiver geometry is used in every version and which stations use the approved locator. When a new pallet shares the general outline but has a different steel receiver or mounting pocket, include a section of each. This prevents approval of an assembly that fits one station configuration while leaving another without a practical trial.
Alignment, stops and datum choices
A pair of locating components may constrain different degrees of freedom depending on the equipment layout. Explain the role of each contact surface in the intended registration scheme, including where clearance is deliberately provided. If the pallet rests on separately supported pads after lifting, show their height relative to the working end of the locator. Identify any adjustable counterpart and specify the documented setup position at which an acceptance check should be performed.
Clear description of the installed references can avoid disagreement between a fixture check and a machine check. An unmounted plastic part may be supported at several locations during measurement, while the installed part bears against a machined carriage face. Note which condition applies for the height, flatness and position requirements. A setup record can include location of the station axis and the way a gauge or sample pallet references the receiver.
Recording repeated movement and wear
During a controlled trial, cycle representative pallets with the intended carrier and note the contact location at entry and in the seated position. Look for alignment changes attributable to the pallet receiver, mounting hardware or nearby guide surfaces. Check that any change in guidance does not shift the point at which the process fixture is released or seated. Record the machine state and the pallet used in the test before comparing the result with a prior version.
If the locator is replaced during maintenance, an old wear pattern can help explain misalignment that a dimensional drawing cannot show. Label photos with the direction of approach and corresponding lift position. Record whether the pattern is concentrated on one side, at the nose tip, or on the base near the fasteners. Where practical, group that evidence with results from an approved new part tested at the same station and settings.
Sample orders and maintenance inventory
A drawing-based inquiry should include the station name or equipment reference, the lift and mating pallet geometry, and the number of variants to be quoted. Specify the material grade, color, and any identification required on the base. If stock may be shared by two plants, identify which assembly differences will be checked before treating the product as interchangeable. Package and label the component so the installation team can distinguish left and right or station variants where relevant.
Plan whether sample approval is intended to establish only fit or to include a defined machine trial. Note which photographs, dimensional checks and production dates are needed for approval. If station trials occur in stages, indicate which parts of the drawing can be frozen after initial fit and which depend on the later trial. For production requests, provide the expected delivery schedule and revision reference alongside the initial and recurring quantities.
Adjusting a station after installation
Before changing the locator position, record the station setup and identify which dimensions are controlled by the pallet, carriage and workholding equipment. If adjustment is allowed, note the starting and final locations using the intended references. The processes upstream and downstream may expect the pallet to occupy a defined position, so a change that improves engagement at one point should also be checked at the next operation. Include known clearance limits around tooling that approaches the pallet after it is seated.
A drawing review can distinguish an adjustable mounting slot from a feature that is present only to provide assembly clearance. If a slot is meant to be adjustable, identify who sets the position and how it will be recorded for service replacement. When a shoulder or pin provides positive location, check that the corresponding feature on the carriage has the same established reference. These details help the maintenance team return to a known location when the original locator reaches the end of its approved service life.
Checking a pallet with asymmetrical features
A pallet fixture may have a receiver to one side of its centerline or different interfaces on its leading and trailing ends. Mark the approach direction and the face visible to the installer. When two locators are used together, record how wear or deflection will be checked at each location. If a loaded pallet behaves differently from an empty one, identify which test conditions apply before measuring repeatability. Keep the original trial conditions with the approved drawing so later results can be interpreted consistently.
Illustrated geometry and sample scope
The illustrated nose, fastener pockets and base show one possible arrangement. Share the dimensions, locator pattern and receiving feature for the actual station. A sample request can include the mounting interface and a matching pallet feature so seating and removal are checked under comparable conditions. The approval team can then mark any areas where a geometry change would affect fit or the working position.
Service check at the lift station
For maintenance use, document whether the receiver can be checked with a reference pallet that remains available between production runs. Verify that its reference surfaces match the pallet version that will use the locator. If the station has adjustable guides, record their approved positions before comparing results between an original locator and a replacement. A worn receiver can make a good locator appear undersize or move the seated pallet away from the expected position. Capture both the receiver condition and the mounting reference to support an accurate follow-up with the equipment team.
Read the SWKS related injection molding design guide or browse the plastic injection parts category.
Request a quotation
Send the drawing, application details and quantities to amanda@tjswks.com or call 0086-15222707659.
Hot Tags: custom pom industrial automation pallet lift locator, China, suppliers, manufacturers, factory, bulk, cheap, low price, quotation, high performance plastic Machine Parts, injection molded plastic parts, injection molding complex parts, PA66 Plastic Special-shaped Parts Injection Molding Parts, Plastic Parts, Soft Tooling Injection Molding






