Asahi Kasei's engineering plastics portfolio lists LEONA™ 15G20, a glass-fiber-reinforced PA66 grade in its high-viscosity group. Gears are among the applications identified by the supplier. For industrial OEMs, the listing provides a candidate to evaluate in a real gear pair, with dimensions and durability judged under the operating conditions that apply to the machine.
Contents
- What does Asahi Kasei list for LEONA™ 15G20?
- What does high viscosity mean for a molded gear?
- Which conditions matter most for durability?
- How can teams compare material candidates?
- How should OEM buyers prepare a trial request?
- What should teams take from the grade listing?
What does Asahi Kasei list for LEONA™ 15G20?
Asahi Kasei identifies 15G20 as a high-viscosity grade in its LEONA polyamide range. Its engineering plastics information describes the grade as glass-fiber-reinforced PA66 and names gears among the applications. The material classification points engineers toward a specific candidate for development where repeated loading and the operating environment matter. The useful starting point for a design review is the exact grade designation and its technical documentation, since the LEONA name covers several formulations.
The official listing offers a material-selection lead for engineers reviewing an existing drive or developing a smaller molded transmission. A gear designer must interpret the grade alongside the intended tooth geometry, mating component, installation fit and changes during service. A supplier's material description gives the design team a formulation to evaluate. The machine's own operating record supplies the information necessary to decide whether that formulation belongs in the assembly. That distinction is also important when purchasers compare an alternate designation or receive an offer for a generic glass-filled nylon.

Illustrative image. Molded polymer gear set and representative precision teeth.
What does high viscosity mean for a molded gear?
High viscosity describes the resin's behavior as it flows through tooling under the conditions used to characterize it. It directs attention to how the chosen grade fills the hub, tooth roots and outer features of an actual mold. A long or restricted flow path can make a grade more demanding to process. After the candidate is confirmed with the resin supplier, the molding team can review the gate and part layout against the desired shape. Optimum conditions will depend on the material documentation, the tool, the molding machine and the gear geometry.
A common mistake in sourcing is to search one property name and treat it as a proxy for every outcome. Resin viscosity does not provide a wear result for two surfaces or a dimension for a finished tooth. Molded samples reveal whether the drawing can be achieved in the planned tool. The development team should compare bore position, concentricity, tooth form and evidence of complete filling in the same review. The material grade and the trial setup must stay in the record. A dimension measured on a machined blank or a hand-finished model may be useful during early evaluation, but production molded parts are the relevant specimens for the production approval.
Which conditions matter most for durability?
Consider a drive that spends part of each cycle under light motion, accelerates through a loaded interval and pauses with one tooth pair engaged. The factors that affect it can include the magnitude and timing of the load, the mating surface, alignment, temperature, moisture and the lubrication policy. A test that runs continuously at a convenient bench setting can miss a transition that matters in the machine. Prepare a representative duty record and identify the condition that warranty or validation teams need to observe. Record whether the drive starts cold, operates warm or is stopped for frequent cleaning.
Glass reinforcement and the use of a polyamide matrix introduce a reason to review dimensions and wear together. Repeat measurements at defined conditions and keep the assembly at the agreed reference temperature and moisture state before comparison. Inspect both members of the gear pair after a representative trial. A surface mark can originate in a worn mating component or an alignment issue, so use matching photos to identify where wear started and what the parts contacted. Before assigning service life, decide whether failure means a damaged tooth, loss of motion accuracy, excessive noise or another equipment-level criterion. Those outcomes call for different measurements.

Illustrative image. Illustrative gear tooth and hub close-up.
How can teams compare material candidates?
Compare gear materials on the same criteria and at the same drawing revision. The aim is to separate material differences from changes to the mold, gear mesh or measurement sequence. If the present drive uses an unreinforced material, review the partner gear's surface and the fit after conditioning as well as the nominal dry dimensions. Where suppliers propose similar grade names, request a technical sheet and sample labels tied to the compounds actually supplied. For work already in production, attach the current approved drawing and disclose the condition that prompted the change.
Record these checks before ordering a trial. During review, compare each report with the specimen's identity, and note how measurements were taken. An unexplained improvement in one test is hard to reproduce without that information. The decision to quote can go ahead with some items still open, provided the quotation describes which evaluation and deliverables are included. The final selection belongs to the documented approval of the material, molding process and gear assembly.
| Review | Input to provide |
|---|---|
| Geometry | Controlled tooth and bore drawing |
| Mesh | Mate and alignment references |
| Environment | Temperature and conditioning history |
| Service | Representative cycling and lubricant |
How should OEM buyers prepare a trial request?
Send a STEP or STP model with the controlled drawing, then show the shaft fit and the operating relationship with the mating gear. Identify which dimensions must be met in a specified conditioned state. Add the allowable backlash or positional error if already controlled in the machine design, and provide the load history, speed range, lubricant and assembly temperature conditions relevant to the trial. Mark tooth, hub and bore surfaces by role. State whether complete gear pairs or single components are required and whether fastening hardware will be furnished by the customer.
A useful request separates the goal of evaluating 15G20 from the authority to specify it in a part drawing. If the grade has already been named by the equipment design group, include the approval revision and ask how its identity will be tracked in sampling. If candidates remain open, say which alternate grades can be considered and which comparison conditions must stay the same. Request traceable parts for the intended tests and define how many pieces will remain as reference samples. Ask the molding supplier about the cavity identification and the inspection report that will accompany the trial.

Illustrative image. Sample gear and inspection setup.
What should teams take from the grade listing?
The Asahi Kasei listing brings grade-specific information to a topic often described only as plastic gearing. LEONA 15G20 gives designers and purchasing staff a concrete PA66 candidate to discuss when gears operate through repeated loading. For sourcing purposes, next steps depend on the design and the reason for evaluation. A worn service gear, a new drawing and a material substitution project each supply different starting data. Give engineers a clear description of the baseline and set the approval criteria before samples are compared.
Where the gear is part of a textile or packaging line, include the installed drive envelope and the access needed for alignment or maintenance. Add the expected run quantity and inspection needs when requesting a tooling review. This allows the buyer to compare a development quotation with the future repeat purchase while keeping the grade approval linked to the specific gear pair and machine application.
Related pages from SWKS include Custom POM Industrial Textile Machine Yarn Feeder Gear and Custom POM Packaging Machine Product Changeover Cam.
Send your drawing, application and order quantity to amanda@tjswks.com for a molding and sample review.

